Read MoreQuick ViewAir Flow Training Unit Hydraulic Lab Equipment Vocational Training Equipment
ZF1129A Air Flow Training Unit Hydraulic Lab Equipment Vocational Training Equipment
The designed of the Air flow taining model should demonstrate to students the principles of compressible fluid flow.
Centrifugal Fan
Capacity : 1,100 CFM
Inlet dia. : approx. 180 mm
Power : 2 hp
Electrical : 415VAC/3-phase/50-60Hz
Multitube Manometer Test Board:
No. of tubes : 14
Materials : clear acrylic
Scale length : 400 mm
Venturi, Orifice and Pitot Tube Flow Measurement Test Sets:
Traversed pitot tube with adjustable scale
Orifice plates (two different sizes)
Venturi nozzle (two different sizes)
Bernoulli’s Theorem Test Set:
Clear acrylic duct with convergence, throat and divergence sections.
Traversed pitot tube installed in centre line of the duct.
Flow Around A Bend:
Acrylic 90o bend squre ducting with a straight section before the bend dimension 60 x 50 mm
(Require FM 21A -Multitube Manometer Test Board)
Flow In Pipes:
Different pipe sections to study:
¨ Duct entry pressure profile
¨ Suden enlargement losses from 65 to 95mm Dia
¨ Friction loss in 2.8m pipe (95mm Dia)
…Velocity of profile in 2.8m (95mm Dia)
(Require – Multitube Manometer Test Board)
Jet Dispersion Test Set:
Traversed pitot tube
Boundary Layer Growth Test Set:
Traversed pitot tube to measure velocity profile at four different locations Reversible flat plate with sharp and blunt leading edges and smooth and roughened surfaces
Smoke Generation System
Includes a smoke generator to demonstrate visually the flow of air around models.
Control Panel:
Fan ON/OFF switch
Variable Speed Drive Controller
Electrical : 415VAC/3-phase/50-60Hz
OVERALL DIMENSIONS
Height : 1.20 m
Depth : 0.75 m
Width : 1.50 m
Brand: Shouldshine
Model:ZF1129A
Read MoreQuick ViewApparatus for studying free and forced vortex flows engineering teaching equipment Fluid Mechanics Experiment Equipment
H13 Apparatus for studying free and forced vortex flows engineering teaching equipment Fluid Mechanics Experiment Equipment for college, vocational training center, university.
Read MoreQuick ViewAssembly Kit For Transformers Construction Transformer Training Equipment Educational Equipment
SR6105E Assembly Kit For Transformers Construction Transformer Training Equipment Educational Equipment
1.Introduction
The transformer assembly kit is for vocational school, technical institution, college, university students doing assembly and disassembly transformer hand on training. It’s for students to see the inside structure of the transformer, be familar with the function for single phase and three phases transformer in different work power.
1.Technical data
It complete with
Single-phase 200V A transformer
Single-phase 600V A transformer
Single-phase 1000V A transformer
three- phase 300V A transformer
three- phase 600V A transformer
and three- phase 1000V A transformer
English operation/instruction manual
Read MoreQuick ViewASSEMBLY KIT OF HYDRO-SANITARY SYSTEMS Teaching Equipment Hydrodynamics Experiment Apparatus
ZM7209B ASSEMBLY KIT OF HYDRO-SANITARY SYSTEMS Teaching Equipment Hydrodynamics Experiment Apparatus for college, vocational training center, university.
Read MoreQuick ViewAutomated pallet storage equipment Didactic Equipment Mechatronics Trainer
ZM3250 Automated pallet storage equipment Didactic Equipment Mechatronics Trainer for college, vocational training center, university.
Read MoreQuick ViewAutomatic Door Training Model Mechatronics Training Equipment Educational Equipment
ZM3168 Automatic Door Training Model Mechatronics Training Equipment Educational Equipment
I.Technical specifications
- Manual/automatic control mode for hardware detection and program calibration.
- An open structure suitable for practical training.
I performance parameters
- Input power: AC220V plus or minus 10% (single phase three-wire);
- Machine power: < 1kVA;
- Dimensions: 1210 x 450 x 1030mm.
Read MoreQuick ViewAutomatic Sorting Robot Trainer Vocational Training Equipment Teaching Equipment
ZM3202 Automatic Sorting Robot Trainer Vocational Training Equipment Teaching Equipment
Picture is only for reference, we supply as technical data
(1) Functions:
A. Its portable size makes it easy to carry out experiments on lab table.
B. The status of input and output signals are monitored and displayed on nearby status LED.
C. Easy cabling-using one single flat cable to connect dsPIC Microcontroller Unit.
(2) dsPIC Microcontroller Unit
A. Functions:
(a) This unit includes a dsPIC30F4011 chip and peripheral I/O circuits, which is very helpful to understand the knowledge related with microprocessor control.
(b) The trainer is protected by a suitcase for easy carrying and storage.
(c) The pins of MCU are protected by photo coupler.
(d) Able to use either TACT or Slide switch as signal input.
MCU : dsPIC30F4011(ISP circuit included)
(a) 6-Bit digital signal controller
(b) 40 Pins or above
(c) 48K byte program memory or above
(d) 2K byte RAM or aljove AC power switch
Reset TACT switch MCU Power LED Input :
(a) TACT switch x14
(b) Slide switch x14
(c) Indicator LED x14
(d) Photocoupler IC x14 Output:
(a) Indicator LED x10
(b) Photocoupler IC x10 Power
(a) input: minimum AC90~264V, 47~63Hz
(b) output :minimum DC 5V/2.5A, DC 3.3V/2.5A, 24V/2A
(3) Automatic Sorting Robot
A. Functions:
(a) Suitable for MCU beginners
(b) Systematic training for trainees
(c) Abundant experimental practices
(d) Widespread control applications
(e) DC motor control, various sensors, pneumatic cylinder control, position control and detection for sliding table, C code programming practice
B. Conveyor module
(a) DC motor control
C. Pick & place robot module
(a) X-Axis DC motor drive
(b) Z-Axis cylinder
(c) R-Axis cylinder
(d) Vacuum generator
(e) 3- slot storing station
(f) Transfer slide
D. Control panel
(a) DC power input: minimum DC 24V
(b) Digital input: 13 or above
(c) Digital output: 7 or above
(d) Extension I/O interface : 40 pins or above
(e) Emergency stop button
E. Module contents :
(a) Belt-conveyor:
i. Driver: minimum DC 24V motor
(b) Sensors:
i. Position sensors, color sensor, metal detector
(c) Sliding table:
i. Driver: minimum DC24V motor
(d) Three-axel handling robot:
i. Pneumatic cylinders,
vacuum generator, Vacuum sucker
(e) Electromagnetic valve :
i. 5/2 way single coil x 2, 5/2 1 way double coil x 1，working
voltage minimum 24V
F. Accessories
(a) 6mm Pneumatic Tube
(b) Three kinds of work piece
(c) 40-pin or above Flat Cable x 1
(d) Experiment Manual
(e) MPLAB IDE Software
G. Air Compressor
(a) Air tank 25L 土 10%
(b) Max. pressure : 10kg/cm2
(c) Flow rate : 90 L/min 士 10%
H. PICkit™3 Programmer
1. Air Supply Unit
(1) 1 HP 10 220 VAC, with 88L ±10% air tank
(2) Flow rate: 185 L/min 土 10%
(3) Max. Pressure: 10 kg/cm2
(4) Include air hose diameter 5x8mm connect to Air Service Unit
Required documents: Manufacturer’s Authorization Letter with contact details and Catalog stating with technical specifications
Warranty: 1 (One) year with services
Read MoreQuick ViewAutomatic System to Operate Industrial Process Mechatronics Training Equipment
ST1125 Automatic System to Operate Industrial Process Mechatronics Training Equipment to college, vocational training centers.
Read MoreQuick ViewAutomatization Didactic Bench with Sensors Educational Equipment Electrician Trainer
ZE3711 Automatization Didactic Bench with Sensors Educational Equipment Electrician Trainer for college, vocational training center, university.
Read MoreQuick ViewAxial flow impeller turbine Teaching Equipment Fluid Mechanics Experiment Equipment
SR210 Axial flow impeller turbine Teaching Equipment Fluid Mechanics Experiment Equipment for college, vocational training center, university.
Read MoreQuick ViewBall Mill Teaching Equipment Thermal Experiment Equipment
SR-CE245 Ball Mill Teaching Equipment Thermal Experiment Equipment for college, vocational training center, university.
Read MoreQuick ViewBasic Electrical Training System Electrical Didactic Equipment Vocational Training Equipment
ZE4120 Basic Electrical Training System Electrical Didactic Equipment Vocational Training Equipment
for college, university, vocational schools.
- Home
- Products
- Electrical Training Equipment
- Mechatronics Training Equipment
- Refrigeration Training Equipment
- Fluid Mechanics Teaching Equipment
- Renewable Training Equipment
- Pneumatic Training Equipment
- Hydraulic Training Workbench
- PCB Lab Equipment
- Building Automation Trainer
- Food Machine Training Equipment
- Microwave Antenna Trainer
- Thermal Training Equipment
- Air Conditioner Trainer
- Vocational Training Equipment
- About Us
- News
- Contact Us