Pneumatic and Electro-pneumatic Bench Didactic Equipment Pneumatic Training Equipment

ZMP1110 Pneumatic and Electro-pneumatic Bench Didactic Equipment Pneumatic Training Equipment    

Pneumatic and electro-pneumatic bench Double-sided mobile workstation allows the assembly and operation of the various components without the use of tools (components equipped with quick assembly system)

–     1* Rolling table dimension between length 1200 mm, height 1700 mm and depth 800 mm minimum.

– 1* extruded and adonized aluminum plate of dimension between 1080 mm length and 680 mm depth minimum with the possibility of fixing the electrical components on both sides.

– 2* cabinet with a minimum of four drawers and locks 

– 1* cable guide

– 1 x power supply unit for mounting frame 220V AC- 24 VDC/ 4A minimum with minimum 6 outputs

– 1 x silent lubricated compressor for classroom use: protected by pressure switch and safety valve                                                                                                                                                           

–  Supply voltage 230V/50HZ

– Operating pressure 7 bar minimum                                                                            

– Suction flow rate 40 L/MIN minimum        

– Tank volume 9 L minimum                                                                           

– Outlet with pressure regulator, pressure gauge and quick coupler

Pre-actuator for manual and mechanical pressurization

–  2 push-button operated 3/2 NC spool valves

– 2 Push-button operated 3/2 NO dispensers

– 1 3/2 NC valve operated by emergency stop button

– 4 Distributors FC 3/2 NC roller-operated

– 2 NC 3/2 directional control valves operated by retractable roller

– 1 Switch operated 3/2 NC bistable valve

– 1 Push button operated 5/2 directional control valve

– 1 5/2-way valve with two-position selector switch

– 1 Closed center 5/3 valve operated by hook-in lever

Pneumatically operated pre-actuator

– 1 Pneumatically operated 3/2 NC monostable spool valve, 3/2 NC.

– 2 Pneumatically operated 5/2 monostable spool valves

– 2 Pneumatically operated 5/2 bistable valves

Signal processing, flow control and blocking

– 1 logic gate “OR”.

– 1 “OR” circuit selector switch

– 1 “AND” logic gate

– 1 “AND” circuit selector switch

– 2 unidirectional flow throttles

– 1 Quick exhaust valve

– 1 Adjustable pneumatic timer with positive output

– 2 Flow regulators with pilot operated check valve

– 1 bi-directional flow restrictor

– 1 Sequence valve

Cylinders

–     2 Single-acting spring return cylinders

– 1 Double-acting cylinder with magnetic piston and elastic damping

– Double acting magnetic piston cylinder with adjustable pneumatic damping

Electro dispensers

– 1 Solenoid valve, 3/2-way monostable NC (24 VDC coil with LED indicator)

– 1 Solenoid valve, 3/2 bistable (24 VDC coil with LED indicator)

– 2 Solenoid valves, 5/2 bistable (24 VDC coil with LED indicator)

– 2 Solenoid valves, 5/2 monostable (24 VDC coil with LED indicator)

– 1 Solenoid valve, 5/3 closed center (24 VDC coil with LED indicator)

– 1 Vacuum generator by suction effect with suction cup

– Control modules/sensors

– 1 ON/OFF switch

– 1 Emergency stop push button (electric)

– 1 Set of electrical inputs (Box with 3 NO-NC pushbuttons)

– 1 Set of 3 relays (3 NO-3 NC, 24VDC coil)

– 1 Indicator (Indicators, ringer)

– 1 Set of 2 timer relays (2 NO- 2 NC)

– 1 Electrical connection terminal block

– 4 Magnetic detectors type Reed

– 2 Static magnetic detectors

– 1 Inductive sensor

– 1 Capacitive sensor

– 1 Photoelectric detector

– 4 Electric limit switch

– 1 Electrical contact pressure switch

– Accessories

– Set of 10 “T” Connectors Ø 4mm

– Set of 10 plastic caps Ø 4mm

– Set of 10 “Y” connectors Ø 4mm

– 1x 4 mm safety laboratory cable set (color red and blue) consisting of at least 80 cables

–  all pneumatic components must be equipped with Ø 4mm quick couplings