Electrical Training Equipment

Electrical Training Equipment

Electrical And Electronics Training Equipment for university,college, vocational training school, technical institute.

  • AC Circuit Electrical Training Equipment Electrical Experiment Equipment

    SR6101E AC Circuit Electrical Training Equipment Electrical Experiment Equipment
    1 Introduction
    In this experiment, three waveforms of sine wave, square wave and triangle wave can be output, and three kinds of waveforms can be used for fine adjustment of frequency, amplitude, linearity and duty ratio. A variety of measuring instruments can be completed by providing three kinds of measuring instruments: AC10V, DC100uA and DC10V. Through the experiment, and master the principle and control mode, the corresponding knowledge and skills, suits, higher vocational colleges, secondary vocational schools and vocational school related professional teaching and skills training examination.
    2.Technical requirement
    Signal Source: 3 mode, Frequency range 1 – 10kHz. Sine, square and triangular. Variable output voltage level on all waveforms 0-10V peak- to-peak nominal, Moving coil meter 0-100 μA movement, scaled 0- 10V peak/mean switchable

  • AC Circuit Output Module Electronics Trainer Vocational Training Equipment

    SR6102E AC Circuit Output Module Electronics Trainer Vocational Training Equipment
    1 Introduction
    This experimental device can provide ac power supply, the output of circuit breaker and fuse protection, can provide 42V/8A and 380V/1A AC. Configuration of digital voltmeter, voltage commutation switch, digital ammeter, can complete a variety of measurements.
    2.Technical data
    Power supply; output: protected with thermal relays and fuses: 42V AC., 8A, 3 phase (380V AC) 1 A for mains voltage version). Instruments: 3-digit electronic voltmeter, switchable on the three phases; 3-digits electronic ammeter,
    3. Detailed technical data
    1. AC380V total power supply —- -4p leakage circuit breaker.
    1. AC42V/8A power supply — -2p circuit breaker.
    2. Three phase indicator light.
    3. Three-phase insurance
    4. Three-phase five-wire output terminal.
    5. AC42V/8A output terminals and insurance.
    6. AC42V/8A output terminals and insurance.
    7. AC42V/8A output indicator light.
    8. Ac voltmeter –AC500V.
    9. Commutation switch
    10. Ac ammeter -AC8A.
    11. AC500V voltmeter measuring control switch (note: set to the left side, with the use of reversing switch, the internal three-phase power supply can be tested; To the right, use the test line to test the voltage of the external output terminal.
    4. Operate instructions
    1. Carefully check whether there is any safety hazard in the power supply line before power supply. (for example, the copper wire of the insulating layer breaks out and is forbidden to be used; Whether the terminal screws are loose)
    2. Connect the terminals on the power supply wire of the three-phase five-wire system in the laboratory (black, green, red, L1, L2, L3; Blue line zero; Double – color ground wire), power supply to the experimental box.
    3. After the check is correct, power the 4P leakage circuit breaker, and the whole device circuit is connected. If you use AC42V/8A power supply, please power the 2P circuit breaker.
    4. When measuring voltage, dial the voltage meter to the left and cooperate with the reversing switch to test the internal three-phase power supply and determine whether the phase is missing; To the right, use the test line to test the voltage on the external output terminals and the ac voltage on other devices.

  • AC/DC Power SSR And Relay Driver Board Electrical Training Equipment

    SR6103E AC/DC Power SSR And Relay Driver Board Electrical Training Equipment Educational Equipment
    1. Introduction
    This experimental device includes two relays: solid-state relays and coil relays, and both have optical decoupling isolation. Through the experiment, and master the principle and control mode, the corresponding knowledge and skills, suits, higher vocational colleges, secondary vocational schools and vocational school related professional teaching and skills training examination.
    2.Technical data
    providing 8 channels of photo-couple isolated solid state relay modules, plus and additional 8 external relay driver outputs.
    3. Operate instructions
    1. Carefully check whether there is any safety hazard in the power supply line before power supply. (for example, the copper wire of the insulating layer breaks out and is not allowed to be used)
    2. Plug the power cord plug into the laboratory socket to power the device.
    3. Use the 2mm safety electrical cable to connect GND with IN, and the relay contact can be moved.

  • Assembly Kit For Transformers Construction Transformer Training Equipment Educational Equipment

    SR6105E Assembly Kit For Transformers Construction Transformer Training Equipment Educational Equipment
    1.Introduction
    The transformer assembly kit is for vocational school, technical institution, college, university students doing assembly and disassembly transformer hand on training. It’s for students to see the inside structure of the transformer, be familar with the function for single phase and three phases transformer in different work power.
    1.Technical data
    It complete with
    Single-phase 200V A transformer
    Single-phase 600V A transformer
    Single-phase 1000V A transformer
    three- phase 300V A transformer
    three- phase 600V A transformer
    and three- phase 1000V A transformer
    English operation/instruction manual

  • DC Compound Machine Trainer Electrical Machine Trainer Educational Equipment

    SR6110E DC Compound Machine Trainer Electrical Machine Trainer Educational Equipment
    1 Introduction
    DC shunt motor is a DC motor equipped with shunt winding and series winding in the main magnetic pole.
    Compound machine excitation winding is divided into two parts, part of the series with the armature winding, the other part with the armature winding in parallel, according to the direction of the magnetic field can be divided into two parts winding generation compound machine and compound machine. Compound DC motor is widely used in ships, trolley buses and lifting mining equipment.
    2 Technical data
    Rated voltage of compound dc motor :42V.
    DC excitation voltage :DC36V;
    Rated speed :3000 RPM.

  • DC Generator Set Trainer Vocational Training Equipment Electrical Machine Trainer

    SR6112E DC Generator Set Trainer Vocational Training Equipment Electrical Machine Trainer
    1 Introduction
    This experimental device includes a DC motor and a three-phase asynchronous motor, which is connected by a coupling. Through the experiment, and master the principle and control mode, the corresponding knowledge and skills, suits, higher vocational colleges, secondary vocational schools and vocational school related professional teaching and skills training examination.
    2 Instructions for the equipment
    1. Three-phase asynchronous motor wiring terminal.
    2. The coupling
    3. Dc compound motor terminal.
    4. The handle
    5. The base plate
    6. Motor base

  • DC Motor Compound Excitation Trainer DC Machine Trainer Educational Equipment

    SR6109E DC Motor Compound Excitation Trainer DC Machine Trainer Educational Equipment
    1 Introduction
    This experimental device can provide DC and AC power supply, and output the protection of fuses, which can provide DC 5V/1.2A, AC 6V/ 1.5A voltage. Configure the moving coil dc 1A and ac 1A pointer table to complete a variety of measurements. Through the experiment, and master the principle and control mode, the corresponding knowledge and skills, suits, higher vocational colleges, secondary vocational schools and vocational school related professional teaching and skills training examination.

  • DC Output Module Electrical Training Equipment Vocational Educational Equipment

    SR6114E DC Output Module Electrical Training Equipment Vocational Educational Equipment
    1 Introduction
    This experimental device can provide DC power supply, and output the protection of fuses, which can provide DC 42V/3A, DC 220V/1A, DC 0-36v /3A, DC 0-230v /1A. Configure digital voltmeter DC500V to complete a variety of measurements. Through the experiment, and master the principle and control mode, the corresponding knowledge and skills, suits, higher vocational colleges, secondary vocational schools and vocational school related professional teaching and skills training examination.
    2 Training panel instruction
    1. DC voltage measurement module — -DC 500V.
    2. DC voltage module -DC 42V/3A.
    3. DC voltage module -DC 220V/1A.
    4. Adjustable DC voltage module -DC 0-36v /3A.
    5. Adjustable DC voltage module -DC 0-230v /1A.
    3.Operation instructions
    1. Carefully check whether there is any safety hazard in the power supply line before power supply. (for example, the copper wire of the insulating layer breaks out and is forbidden to be used; Whether the terminal screws are loose)
    2. Plug the power cord into the power outlet on the left side of the device, and turn on the power switch after checking. The four dc voltage modules on the front panel can be used at will.
    3. When measuring voltage, use the 4mm safety electrical cable to connect to the signal input terminal of the dc voltage measurement module.

  • DC Shunt Wound Machine Trainer Electrical Training Equipment Teaching Model

    SR6111E DC Shunt Wound Machine Trainer Electrical Training Equipment Teaching Model
    1 Introduction
    DC compound motor is a DC motor equipped with shunt winding and series winding in the main magnetic pole.
    Compound machine excitation winding is divided into two parts, part of the series with the armature winding, the other part with the armature winding in parallel, according to the direction of the magnetic field can be divided into two parts winding generation compound machine and compound machine. Compound DC motor is widely used in ships, trolley buses and lifting mining equipment.
    2 Technical data
    Rated voltage of compound dc motor :42V.
    DC excitation voltage :DC36V;
    Rated speed :3000 RPM.

  • DC Speed Control Module Electrical Machine Trainer Vocational Training Equipment

    SR6113E DC Speed Control Module Electrical Machine Trainer Vocational Training Equipment
    1 Introduction
    This experimental device can provide excitation voltage and armature voltage for DC motor, and the armature voltage can be adjusted between DC 0 and 220V to realize speed control of DC motor. Through the experiment, and master the principle and control mode, the corresponding knowledge and skills, suits, higher vocational colleges, secondary vocational schools and vocational school related professional teaching and skills training examination.
    2 Training Panel Instructions
    1. Enable switch
    2. Adjustment of soft start time.
    3. Excitation voltage output terminal –DC 220V/0.5A.
    4. Dual control switch — power switch.
    5. Current limit adjustment.
    6. Potentiometer — armature voltage adjustment.
    7. Armature voltage output terminal –DC 0-220v /4A.
    8.Fuse
    9. Power socket –AC220V power supply.
    3 Operation instruction
    1. Carefully check whether there is any safety hazard in the power supply line before power supply. (for example, the copper wire of the insulating layer breaks out and is not allowed to be used)
    2. Insert the power cord plug into the AC22V power input socket and power the panel.
    3. The test cases on the excitation voltage output terminals using K4 test line is connected to the dc motor excitation winding terminals, the armature voltage output terminals on the test chamber used K4 test line connected to the dc motor armature winding wiring terminals. (dc motor shunt connection mode is adopted here)
    4. It will enable the single control button and power double control button to hit OFF state, and the potentiometer will rotate counterclockwise to the minimum. After checking, turn on the power double control button, and the whole device circuit is connected. Turn on the switch and adjust the potentiometer to adjust the speed of the dc motor.

  • Electromagnetism And Magnetic Circuit Trainer Electrical Training Equipment

    SR6127E Electromagnetism And Magnetic Circuit Electrical Training Equipment Didactic Equipment
    1 Introduction
    The training device through the relevant experiment, can be familiar with magnetic material of the surface magnetic field distribution, master the principle of hall effect, trains the student to the corresponding knowledge and skills, suits, higher vocational colleges, secondary vocational schools and vocational school the teaching of related professional schools.
    2 Technical data
    (1) input power: dc power supply 0-5v + 10% 60Hz.
    (2) weight: < 25kg.
    (3) working conditions: temperature – 10 ℃ ~ + 40 ℃
    Relative humidity < 85% (25 ℃)

  • Energy Control Trainer Vocational Education Equipment Teaching Equipment

    SR6128E Energy Control Trainer Vocational Education Equipment Teaching Equipment
    I. Introduction
    This experimental device simulates the power supply network. “Energy control the trainer” model in a typical industrial building energy distribution and management are widely used in the study, through the experiment, to master the principle and control mode, the corresponding knowledge and skills, suits, higher vocational colleges, secondary vocational schools and vocational school related professional teaching and skills training examination
    II. Training panel instruction
    1. Phase change switch
    2. AC ammeter –AC 5A.
    3. AC voltmeter -AC 450V.
    4. Molded case circuit breaker –AC 40A.
    5. Transformer — 10:51t.
    6. Single-phase electronic meter.
    7. Leakage circuit breaker –DZ47sLE/20A/2P.
    8. Wall switch
    9. Lamp holder
    10. Three-phase four-wire electronic active power meter.
    11. Ground wire cable
    12. Zero cable
    III. Operate instructions
    1. Carefully check whether there is any safety hazard in the power supply line before power supply. (for example, the copper wire of the insulating layer breaks out and is not allowed to be used)
    2. Connect the three-phase power supply of the laboratory to the molded case circuit breaker, and connect the zero and ground lines to the zero line and ground line.
    3. After check and correct, switch the circuit breaker switch to “ON”, switch the 2P circuit breaker, turn ON the wall switch, and turn ON the light bulb, so that the whole power supply system is fully supplied.